View 0ICAH-002-XTD_4226575.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AMIS-42670 High-Speed CAN Transceiver
For Long Networks
Data Sheet
1.0 General Description
The AMIS-42670 CAN transceiver is the interface between a controller area network (CAN) protocol controller and the physical bus and may be used in both 12V and 24V systems. The transceiver provides differential transmit capability to the bus and differential receive capability to the CAN controller. Due to the wide common-mode voltage range of the receiver inputs, the AMIS-42670 is able to reach outstanding levels of electromagnetic susceptibility (EMS). Similarly, extremely low electromagnetic emission (EME) is achieved by the excellent matching of the output signals. The AMIS-42670 is the industrial version of the AMIS-30660 and primarily intended for applications where long network lengths are mandatory. Examples are elevators, in-building networks, process control and trains. To cope with the long bus delay the communication speed needs to be low. AMIS-42670 allows low transmit data rates down 10 Kbit/s or lower.
2.0 Key Features
* * * * * * * * * * * * * Fully compatible with the ISO 11898-2 standard Certified "Authentication on CAN Transceiver Conformance (d1.1)" Wide range of bus communication speed (0 up to 1 Mbit/s) Allows low transmit data rate in networks exceeding 1 km Ideally suited for 12V and 24V industrial and automotive applications Low electromagnetic emission (EME) common-mode choke is no longer required Differential receiver with wide common-mode range (+/- 35V) for high EMS No disturbance of the bus lines with an un-powered node Thermal protection Bus pins protected against transients Silent mode in which the transmitter is disabled Short circuit proof to supply voltage and ground Logic level inputs compatible with 3.3V devices
3.0 Technical Characteristics
Table 1: Technical Characteristics Symbol Parameter VCANH DC voltage at pin CANH VCANL DC voltage at pin CANL Vi(dif)(bus_dom) Differential bus output voltage in dominant state tpd(rec-dom) Propagation delay TxD to RxD tpd(dom-rec) Propagation delay TxD to RxD CM-range Input common-mode range for comparator VCM-peak VCM-step Common-mode peak Common-mode step
Conditions 0 < VCC < 5.25V; no time limit 0 < VCC < 5.25V; no time limit 42.5 < RLT < 60 See Figure 7 See Figure 7 Guaranteed differential receiver threshold and leakage current See Figures 8 and 9 (Notes) See Figures 8 and 9 (Notes)
Min. -45 -45 1.5 70 100 -35 -500 -150
Max. +45 +45 3 245 245 +35 500 150
Unit V V V ns ns V mV mV
Note: The parameters VCM-peak and VCM-step guarantee low electromagnetic emission.
4.0 Ordering Information
Ordering Code (Tubes) 0ICAH-002-XTD Ordering Code (Tape) 0ICAH-002-XTP Marketing Name AMIS 42670NGA Package SOIC-8 GREEN Temp. Range -40C...125C
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
1
AMIS-42670 High-Speed CAN Transceiver
For Long Networks 5.0 Block Diagram
VCC S
8
VCC
Data Sheet
3 Thermal shutdown
7
TxD
Driver control 1 6
CANH CANL
AMIS-42670 RxD VREF
4
COMP
Ri(cm) +
Vcc/2
5
Ri(cm) 2
PD20070831.4
GND
Figure 1: Block Diagram
6.0 Typical Application
6.1 Application Schematic
VBAT
IN
5V-reg
OUT VCC S
8 3 7
60
60 47 nF
VCC CANH VREF CANL 60 GND
CAN controller
RxD TxD
4
AMIS42670
2
5 6
CAN BUS
1
60 47 nF
PC20070831.3
GND
Figure 2: Application Diagram
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
2
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
6.2 Pin Description 6.2.1. Pin Out (Top View)
Data Sheet
TxD GND VCC RxD
1
8
S CANH CANL VREF
AMIS42670
Figure 3: Pin Configuration
2 3 4
7 6 5
PC20070831.2
6.3 Pin Description
Table 2: Pin Out Pin Name 1 TxD 2 GND 3 VCC 4 RxD 5 VREF 6 CANL 7 CANH 8 S
Description Transmit data input; low input dominant driver; internal pull-up current Ground Supply voltage Receive data output; dominant transmitter low output Reference voltage output Low-level CAN bus line (low in dominant mode) High-level CAN bus line (high in dominant mode) Silent mode control input; internal pull-down current
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
3
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
Data Sheet
7.0 Functional Description
7.1 Operating Modes The behavior of AMIS-42670 under various conditions is illustrated in Table 3 below. In case the device is powered, one of two operating modes can be selected through pin S.
Table 3: Functional table of AMIS-42670; X = don't care VCC 4.75 to 5.25.V 4.75 to 5.25.V 4.75 to 5.25.V VCC2V pin S 0 (or floating) 1 X X X pin CANH High VCC/2 VCC/2 0V7.1.1. High-Speed Mode If pin S is pulled low (or left floating), the transceiver is in its high-speed mode and is able to communicate via the bus lines. The signals are transmitted and received to the CAN controller via the pins TxD and RxD. The slopes on the bus line outputs are optimized to give extremely low electromagnetic emissions. 7.1.2. Silent Mode In silent mode, the transmitter is disabled. All other IC functions continue to operate. The silent mode is selected by connecting pin S to VCC and can be used to prevent network communication from being blocked, due to a CAN controller which is out of control. 7.2 Over-temperature Detection A thermal protection circuit protects the IC from damage by switching off the transmitter if the junction temperature exceeds a value of approximately 160C. Because the transmitter dissipates most of the power, the power dissipation and temperature of the IC is reduced. All other IC functions continue to operate. The transmitter off-state resets when pin TxD goes high. The thermal protection circuit is particularly necessary when a bus line short-circuits. 7.3 High Communication Speed Range The transceiver is primarily intended for industrial applications. It allows very low baud rates needed for long bus length applications. But also high speed communication is possible up to 1Mbit/s. 7.4 Fail-safe Features A current-limiting circuit protects the transmitter output stage from damage caused by an accidental short-circuit to either positive or negative supply voltage, although power dissipation increases during this fault condition. The pins CANH and CANL are protected from automotive electrical transients (according to "ISO 7637"; see Figure 4). Pin TxD is pulled high internally should the input become disconnected.
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
4
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
Data Sheet
8.0 Electrical Characteristics
8.1 Definitions All voltages are referenced to GND (pin 2). Positive currents flow into the IC. Sinking current means the current is flowing into the pin; sourcing current means the current is flowing out of the pin. 8.2 Absolute Maximum Ratings Stresses above those listed in the following table may cause permanent device failure. Exposure to absolute maximum ratings for extended periods may affect device reliability.
Table 4: Absolute Maximum Ratings Symbol Parameter VCC Supply voltage VCANH DC voltage at pin CANH VCANL DC voltage at pin CANL VTxD DC voltage at pin TxD VRxD DC voltage at pin RxD VS DC voltage at pin S VREF DC voltage at pin VREF Vtran(CANH) Transient voltage at pin CANH Vtran(CANL) Transient voltage at pin CANL Vesd Latch-up Tstg Tamb Tjunc
Notes: 1. 2. 3. 4.
Conditions 0 < VCC < 5.25V; no time limit 0 < VCC < 5.25V; no time limit
Electrostatic discharge voltage at all pins Static latch-up at all pins Storage temperature Ambient temperature Maximum junction temperature
Note 1 Note 1 Note 2 Note 4 Note 3
Min. -0.3 -45 -45 -0.3 -0.3 -0.3 -0.3 -150 -150 -4 -750 -55 -40 -40
Max. +7 +45 +45 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 +150 +150 +4 +750 100 +155 +125 +150
Unit V V V V V V V V V kV V mA C C C
Applied transient waveforms in accordance with ISO 7637 part 3, test pulses 1, 2, 3a, and 3b (see Figure 4). Standardized human body model ESD pulses in accordance to MIL883 method 3015.7. Static latch-up immunity: static latch-up protection level when tested according to EIA/JESD78. Standardized charged device model ESD pulses when tested according to EOS/ESD DS5.3-1993.
8.3 Thermal Characteristics
Table 5: Thermal Characteristics Symbol Parameter Rth(vj-a) Thermal resistance from junction to ambient in SO8 package Rth(vj-s) Thermal resistance from junction to substrate of bare die
Conditions In free air In free air
Value 150 45
Unit K/W K/W
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
5
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
8.4 DC and Timing Characteristics VCC = 4.75 to 5.25V; Tjunc = -40 to +150C; RLT =60 unless specified otherwise.
Table 6: DC and Timing Characteristics Symbol Parameter Supply (Pin VCC) ICC Supply current Transmitter Data Input (Pin TxD) VIH High-level input voltage VIL Low-level input voltage IIH High-level input current IIL Low-level input current Ci Input capacitance Mode Select (Pin S) VIH High-level input voltage VIL Low-level input voltage IIH High-level input current IIL Low-level input current Receiver Data Output (Pin RxD) VOH High-level output voltage VOL Low-level output voltage Reference Voltage Output (Pin VREF) VREF Reference output voltage VREF_CM Reference output voltage for full common mode range Bus Lines (Pins CANH and CANL) Vo(reces)(CANH) Recessive bus voltage at pin CANH Vo(reces)(CANL) Recessive bus voltage at pin CANL Io(reces) (CANH) Recessive output current at pin CANH Io(reces) (CANL) Vo(dom) (CANH) Vo(dom) (CANL) Vi(dif) (bus) Recessive output current at pin CANL Dominant output voltage at pin CANH Dominant output voltage at pin CANL Differential bus input voltage (VCANH - VCANL) Short circuit output current at pin CANH Short circuit output current at pin CANL Differential receiver threshold voltage Differential receiver threshold voltage for high common-mode Differential receiver input voltage hysteresis Common-mode input resistance at pin CANH Common-mode input resistance at pin CANL Matching between pin CANH and pin CANL common-mode input resistance Differential input resistance Matching between pin CANH and pin CANL common-mode input resistance Differential input resistance Conditions Dominant; VTXD = 0V Recessive; VTXD = VCC Output recessive Output dominant VTxD = VCC VTxD = 0V Not tested Silent mode High-speed mode VS =2V VS =0.8V IRXD = - 10mA IRXD = 6mA -50A < IVREF < +50A -35V Data Sheet
Unit mA mA V V A A pF V V A A V
0.45 0.55 x VCC 0.60 x VCC 3.0 3.0 +2.5 +2.5 4.25 1.75 3.0 +50 -95 120 0.9 1.05 100 37 37 +3 75 +3 75
V V V V V mA mA V V V mV mA mA V V mV K K % K % K
Io(sc) (CANH) Io(sc) (CANL) Vi(dif)(th) Vihcm(dif) (th) Vi(dif) (hys) Ri(cm)(CANH) Ri(cm) (CANL) Ri(cm)(m) Ri(dif) Ri(cm)(m) Ri(dif)
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
6
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
Table 7: DC and Timing Characteristics (continued) Symbol Parameter Ci(CANH) Input capacitance at pin CANH Ci(CANL) Input capacitance at pin CANL Ci(dif) Differential input capacitance ILI(CANH) Input leakage current at pin CANH ILI(CANL) Input leakage current at pin CANL VCM-peak Common-mode peak during transition from dom rec or rec dom VCM-step Difference in common-mode between dominant and recessive state Power-on-Reset (POR) PORL POR level Thermal Shutdown Tj(sd) Shutdown junction temperature Timing Characteristics (see Figure 6 and Figure 7) td(TxD-BUSon) Delay TxD to bus active td(TxD-BUSoff) Delay TxD to bus inactive td(BUSon-RxD) Delay bus active to RxD td(BUSoff-RxD) Delay bus inactive to RxD tpd(rec-dom) Propagation delay TxD to RxD from recessive to dominant td(dom-rec) Propagation delay TxD to RxD from dominant to recessive Conditions VTxD = VCC; not tested VTxD = VCC; not tested VTxD = VCC; not tested VCC = 0V; VCANH = 5V VCC = 0V; VCANL = 5V See Figure 8 and Figure 9 See Figure 8 and Figure 9 CANH, CANL, Vref in tristate below POR level Min. Typ. 7.5 7.5 3.75 170 170 Max. 20 20 10 250 250 500 150 3.5 160 85 60 55 100 4.7 180 130 105 105 135 245 245
Data Sheet
10 10 -500 -150 2.2 150
Unit pF pF pF A A mV mV V C ns ns ns ns ns ns
Vs = 0V Vs = 0V Vs = 0V Vs = 0V Vs = 0V Vs = 0V
40 30 25 65 70 100
8.5 Measurement Set-ups and Definitions
+5 V 100 nF
3
VCC
7 1
TxD
CANH 1 nF VREF 1 nF
AMIS42670
RxD
4 8 2
5
Transient Generator
6
CANL
PC20070831.1
20 pF
S
GND
Figure 4: Test Circuit for Transients
VRxD High Low
Hysteresis PC20040829.7
0,5
0,9
Vi(dif)(hys)
Figure 5: Hysteresis of the Receiver
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
7
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
+5 V 100 nF
3
Data Sheet
VCC
7 1
TxD
CANH RLT VREF 60 CLT 100 pF
AMIS42670
RxD
4 8 2
5
6
CANL
PC20070831.5
20 pF
S
GND
Figure 6: Test Circuit for Timing Characteristics
TxD
HIGH LOW
CANH
CANL
dominant
Vi(dif) = VCANH - VCANL
0,9V
0,5V recessive
RxD td(TxD-BUSon) tpd(rec-dom)
0,3 x VCC 0,7 x VCC
td(TxD-BUSoff) td(BUSon-RxD) tpd(dom-rec) td(BUSoff-RxD)
PC20040829.6
Figure 7: Timing Diagram for AC Characteristics
AMI Semiconductor - October 07, Rev. 1.0 www.amis.com Specifications subject to change without notice
8
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
Data Sheet
+5 V 100 nF
3
VCC
7 1
TxD
CANH
6.2 k 10 nF Active Probe
Generator RxD
4
AMIS42670
CANL 6 6.2 k
5
Spectrum Anayzer
8
2
30 VREF
30
20 pF
S
GND
47 nF
PC20070831.6
Figure 8: Basic Test Set-up for Electromagnetic Measurement
CANH
CANL
recessive
Vi(com) = VCANH + VCANL VCM-peak
VCM-step
VCM-peak
PC20040829.7
Figure 9: Common-mode Voltage Peaks (see measurement set-up Figure 8)
AMI Semiconductor - October 07, Rev. 1.0
9
www.amis.com Specifications subject to change without notice
AMIS-42670 High-Speed CAN Transceiver
For Long Networks
Data Sheet
9.0 Package Outline
SOIC-8: Plastic small outline; eight leads; body width 150mil
AMI Semiconductor - October 07, Rev. 1.0
10
www.amis.com Specifications subject to change without notice
AMIS-42670 High-Speed CAN Transceiver
For Long Networks 10.0 Soldering
10.1 Introduction
Data Sheet
This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in the AMIS "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed circuit boards with high population densities. In these situations reflow soldering is often used. 10.2 Re-flow Soldering Re-flow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for re-flowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds, depending on heating method. Typical reflow peak temperatures range from 215 to 250C. The top-surface temperature of the packages should preferably be kept below 230C. 10.3 Wave Soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used, the following conditions must be observed for optimal results: * Use a double-wave soldering method, comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. For packages with leads on two sides and a pitch (e): o Larger than or equal to 1.27mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board. o Smaller than 1.27mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. * For packages with leads on four sides, the footprint must be placed at a 45 degree angle to the transport direction of the printedcircuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is four seconds at 250C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 10.4 Manual Soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to ten seconds at up to 300C. When using a dedicated tool, all other leads can be soldered in one operation within two to five seconds, between 270 and 320C.
Table 8: Soldering
Package Soldering Method Wave Not suitable Not suitable (2) Suitable Not recommended (3)(4) Not recommended (5) Reflow (1) Suitable Suitable Suitable Suitable Suitable
BGA, SQFP HLQFP, HSQFP, HSOP, HTSSOP, SMS PLCC (3) , SO, SOJ LQFP, QFP, TQFP SSOP, TSSOP, VSO
Notes: 1. 2. 3. 4. 5.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods." These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heat sink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). If wave soldering is considered, then the package must be placed at a 45 degree angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65mm. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5mm.
AMI Semiconductor - October 07, Rev. 1.0
11
www.amis.com Specifications subject to change without notice
AMIS-42670 High-Speed CAN Transceiver
For Long Networks 11.0 Company or Product Inquiries
Data Sheet
For more information about AMI Semiconductor's high-speed Industrial CAN transceivers, visit our Web site at: http://www.amis.com
12.0 Document History
Date October 2007 Revision 1.0 Change Initial release
Devices sold by AMIS are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AMIS makes no warranty, express, statutory, implied or by description, regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. AMIS makes no warranty of merchantability or fitness for any purposes. AMIS reserves the right to discontinue production and change specifications and prices at any time and without notice. AMI Semiconductor's products are intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment, are specifically not recommended without additional processing by AMIS for such applications. Copyright (c)2007 AMI Semiconductor, Inc.
AMI Semiconductor - October 07, Rev. 1.0
12
www.amis.com Specifications subject to change without notice

▲Up To Search▲

Price & Availability of 0ICAH-002-XTD

	To Download 0ICAH-002-XTD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .